QuickTalker FT (7, 12 and 23)

Overview

• FT‑7: 7 message locations, up to 5 recording levels (23 messages total)

• FT‑12: 12 message locations, up to 5 levels (approx. 52 messages) - ideal for two-user communication boards

• FT‑23: 23 message locations, 5 levels (up to 103 messages), built for advanced users.

Each uses a FeatherTouch membrane - so messages can be recorded/re-triggered with minimal force, making them highly accessible. 

Getting Started with the QuickTalker FeatherTouch

Setting up

1. Turn the device over and remove the battery cover.
2. Insert 4 × AA alkaline batteries, then replace the cover.
3. Slide your printed symbol overlay under the clear cover on the front.
4. Turn the QuickTalker FT on.
5. Choose a recording level using the Level Selection button.
6. Press and hold the Record button until the red Recording Indicator Light turns on, then release.
7. Press and release the message location you want to record.
8. Speak clearly into the microphone.
9. Press that same message location again to stop recording.
10. Repeat for other locations.
11. Press the Record button again to turn the indicator light off and exit record mode.
    
    

Using the product (with practical examples)

Playing a message

Just press one of the message locations. The recorded message plays immediately.

Using Core Messages

The three core message locations stay the same across all five levels - ideal for repeated classroom phrases such as:

• “Yes”
• “Help please”
• “Finished”

These are recorded once and remain available no matter which level you select.

Using Levels

Levels allow you to create different sets of messages, such as:

• Level 1: morning routine
• Level 2: literacy activities
• Level 3: snack choices
• Level 4: story comments
• Level 5: home messages

To change level: press Level Selection until you see the correct Level Indicator.

Each level can hold nine messages (core messages stay the same on all levels).

Clearing messages

Clear all messages on the current level

1. Select the level.
2. Hold the Record button for 10 seconds until the device beeps.
3. Only messages on that level are cleared (core messages remain).

Clear all messages on the whole device, including core messages

1. Hold the Record button for 30 seconds.
2. You’ll hear one beep series at 10 seconds - keep holding.
3. A second beep series at 30 seconds confirms everything has been erased.
   
   

Troubleshooting

If you can’t change levels or you want to prevent the articles from being changed please visit this article to find out how to lock and unlock the device.

If the QuickTalker FT is not playing messages correctly or you want to erase messages, please visit this article for instructions.

You can visit the QuickTalker FT Support Hub on the Ablenet website for additional support resources. 

Care, Maintenance & Cleaning

Cleaning (before disinfecting)

1. Turn off the device and remove the batteries.
2. Remove visible dirt or debris.
3. Wipe the device with general cleaning wipes.
4. Use a cotton swab for tight areas.
5. Let it fully dry.

Disinfecting

1. Device must be off with batteries removed.
2. Use wipes/towels containing Virucidal, Bactericidal, Pseudomonacidal, Tuberculocidal, or Fungicidal agents.
3. Ensure surfaces stay wet for at least 4 minutes.
4. Allow to air-dry completely.

Reuse guidance

Inspect before reuse for cracks, corrosion, or wear. If anything looks damaged, stop using the device.

Downloadable Resources

• QuickTalker 7, 12, 23 Quick Start Guide
• QuickTalker FT 7 Instructions for Use
• QuickTalker FT 12 Instructions for Use
• QuickTalker FT 23 Instructions for Use

Warranty

If any part of this article was unclear, or you think there is something missing (extra steps, examples or images etc.), let us know and we'll update the article:
Support article feedback form